Experimental investigation of electrochemical machining performance of AISI 304 stainless steel using a palladium-coated electrode with ascorbic acid - mixed electrolyte
Original scientific paper
DOI:
https://doi.org/10.5599/jese.3660Keywords:
Electrochemical metal manufacturing, electrolyte composition, machining voltage, duty cycle, pulse frequency, machining rate, overcutAbstract
Passive film generation, buildup of insoluble hydroxide sludge, and dimensional errors caused by uncontrolled anodic dissolution are issues that arise during electrochemical machining (ECM) of AISI 304 stainless steel (SS). While electrode coatings and electrolyte additives have been studied separately, the combination of palladium (Pd)-coated electrodes and ascorbic acid-modified electrolytes to enhance ECM performance has received less attention. Using a Pd-coated needle electrode and a sodium nitrate (NaNO3) electrolyte containing 10 g L-1 ascorbic acid, this study experimentally analyses the machining properties of AISI 304 SS. The effects on machining rate (MR) and overcut (OC) of electrolyte concentration (0.328 to 0.386 mol L-2), machining voltage (7 to 12 V), duty cycle (40 to 90 %), and pulse frequency (40 to 90 Hz) were methodically assessed. The machined-hole shape was examined using scanning electron microscopy (SEM), and the electrode substrate was characterized using energy-dispersive X-ray spectroscopy. Experimental data show that increasing electrolyte concentration, machining voltage, duty cycle, and pulse frequency enhanced MR and decreased OC within the examined ranges. With a 58.4 % improvement in MR from 0.219 to 0.347 μm s-1 and a 23.4 % decrease in OC from 290 to 222 μm when frequency increased from 40 to 90 Hz, pulse frequency showed the greatest increase in MR. At an electrolyte concentration of 0.386 mol L-1, a machining voltage of 12 V, a 90 % duty cycle, and a pulse frequency of 90 Hz, the maximum recorded MR of 0.347 μm s-1 with an OC of 222 μm was attained. Nearly circular machined holes with comparatively clean edges and few surface deposits were visible in SEM examinations, suggesting regulated anodic dissolution. By reducing Fe3+ to Fe2+, ascorbic acid is suggested to prevent the formation of insoluble ferric hydroxide, promoting electrolyte stability and eliminating reaction products. Using a Pd-coated electrode and an electrolyte modified with ascorbic acid, the study determines an experimentally assessed processing window for ECM of AISI 304 stainless steel, offering insights into increasing machining productivity and dimensional correctness.
Downloads
References
[1] H. M. Yehia, F. Nouh, O. A. El-Kady, W. Abd-Elaziem, E. M. Elsayed, Studying the microstructure, electrical, and electrochemical behaviour of the Cu-10WC/x GNs for electrochemical machining electrode and energy application, International Journal of Machining and Machinability of Materials 24 (2022) 430-452. https://doi.org/10.1504/IJMMM.2022.128461 DOI: https://doi.org/10.1504/IJMMM.2022.128461
[2] Q. C. Kong, G. L. Liu, J. L. Song, Q. F. Tan, G. Z. Liu, S. Q. Zhao, Preparation of sidewall-insulation layer on micro-hollow electrodes for ECM by asymmetric-timed bipolar electrophoretic coating method and its application, Precision Engineering 67 (2021) 24-35. https://doi.org/10.1016/j.precisioneng.2-020.09.001 DOI: https://doi.org/10.1016/j.precisioneng.2020.09.001
[3] J.-C. Hung, Y.-R. Liu, H.-P. Tsui, Z.-W. Fan, Electrode insulation layer for electrochemical machining fabricated through hot-dip aluminizing and microarc oxidation on a stainless-steel substrate, Surface and Coatings Technology 378 (2019) 124995. https://doi.org/10.10-16/j.surfcoat.2019.124995 DOI: https://doi.org/10.1016/j.surfcoat.2019.124995
[4] J. Hung, H. Liu, Y. Chang, K. Hung, S. Liu, Development of helical electrode insulation layer for electrochemical microdrilling. Procedia CIRP 6 (2013) 373-377. https://doi.org/10.1016/j.procir.2013.03.045 DOI: https://doi.org/10.1016/j.procir.2013.03.045
[5] A. K. Swain, M. M. Sundaram, K. P. Rajurkar, Use of coated microtools in advanced manufacturing: An exploratory study in electrochemical machining (ECM) context, Journal of Manufacturing Processes 14 (2012), 150-159. https://doi.org/10.1016/j.jmapro.2011.11.005 DOI: https://doi.org/10.1016/j.jmapro.2011.11.005
[6] J.-C. Hung, P.-C. Chen, Characteristics research of different electrode tip shapes by electrodeposition for micro slot ECM, Procedia CIRP 95 (2020) 798-802. https://doi.org/10.1016/j.procir.2020.02.327 DOI: https://doi.org/10.1016/j.procir.2020.02.327
[7] G. H. Liu, Y. Li, X. P. Chen, S. J. Lv, Research on side-insulation of tool electrode for micro electrochemical machining, Advanced Materials Research 60 (2009) 380-387. https://doi.org/10.4028/www.scientific.net/AMR.60-61.380 DOI: https://doi.org/10.4028/www.scientific.net/AMR.60-61.380
[8] G. Liu, Y. Li, Q. Kong, H. Tong, H. Zhong, Silicon-based tool electrodes for micro electrochemical machining, Precision Engineering 52 (2018) 425-433. https://doi.org/10.1016/j.precisioneng.2018.02.003 DOI: https://doi.org/10.1016/j.precisioneng.2018.02.003
[9] L. Guodong, L. Yong, K. Quancun, T. Hao, Selection and optimization of electrolyte for micro electrochemical machining on stainless steel 304, Procedia CIRP 42 (2016) 412-417. https://doi.org/10.1016/j.procir.2016.02.223 DOI: https://doi.org/10.1016/j.procir.2016.02.223
[10] M. Tak, S. V. Reddy A. Mishra, R. G. Mote, Investigation of pulsed electrochemical micro-drilling on titanium alloy in the presence of complexing agent in electrolyte, Journal of Micromanufacturing 1 (2018) 142-153. https://doi.org/10.1177/2516598418784682 DOI: https://doi.org/10.1177/2516598418784682
[11] A. Sethi, B. R. Acharya, P. Saha, Electrochemical dissolution of WC-Co micro-tool in micro-WECM using an Eco-friendly citric acid mixed NaNO3 electrolyte, Journal of The Electrochemical Society 169 (2022) 033503. https://doi.org/ 10.1149/1945-7111/ac54d9 DOI: https://doi.org/10.1149/1945-7111/ac54d9
[12] G. Cercal, G. de Alvarenga, M. Vidotti, Sludge reduction and surface investigation in electrochemical machining by complexing and reducing agents, Processes 11 (2023) 2186. https://doi.org/10.3390/pr11072186 DOI: https://doi.org/10.3390/pr11072186
[13] M. Zohoor, S. Jalili, A. Alipour, R. Mosallanejad, Effect of electrolyte type on electrochemical machining of 304 steel, International Journal of Applied Engineering Research 12 (2016) 20-39. https://www.ripublication.com/ijaer.htm
[14] D. Janardhanan, H. Perianna, Experimental investigation on the suitability of dual fluid system-assisted ECM (DF-ECM) and the influence of magnet in machining of SS304, The International Journal of Advanced Manufacturing Technology 130 (2024) 3819-3836. https://doi.org/10.1007/s00170-024-12957-6 DOI: https://doi.org/10.1007/s00170-024-12957-6
[15] V. N. Najm, M. M. Abdulrazaq, A. M. S. Ahmed, Enhancing surface integrity of 316 SS with ecofriendly electrolyte in electrochemical machining, Advances in Science and Technology. Research Journal 19 (2025) 109-119. https://doi.org/10.12913/22998624/210085 DOI: https://doi.org/10.12913/22998624/210085
[16] N. K. Jain, V. K. Jain, Optimization of electro-chemical machining process parameters using genetic algorithms, Machining Science and Technology 11 (2007) 235-258. https://doi.org/10.1080/10910340701350108 DOI: https://doi.org/10.1080/10910340701350108
[17] R. Mishra, R. P. Singh, R. K. Garg, Investigation into micro slotting of Cu-based shape memory alloy via µ-ECM using ethylene glycol mixed aqueous NaCl electrolyte, Canadian Metallurgical Quarterly 64 (2025) 1063-1077. https://doi.org/10.1080/00084433.2024.2419224 DOI: https://doi.org/10.1080/00084433.2024.2419224
[18] S. Wang, W. Wei, Y. Gao, H. Pan, Y. Wang, Characterization of Ti–Zr–V thin films deposited by DC and unipolar pulsed DC magnetron sputtering, Vacuum 188 (2021) 110200. https://doi.org/10.1016/j.vacuum.2021.110200 DOI: https://doi.org/10.1016/j.vacuum.2021.110200
[19] Y. Ni, W. Wang, C. Tang, J. Sun, W. Zhang, W. Gao, J. Zou, Optimizing coverage of palladium nanoparticles for a highly sensitive hydrogen gas sensor based on nanogaps via spray-deposition, Journal of Materials Science: Materials in Electronics 35 (2024) 770. https://doi.org/10.1007/s10854-024-12537-0 DOI: https://doi.org/10.1007/s10854-024-12537-0
[20] N. Sivashankar, K. Santhanam, S. Prasad, M. Jawahar, R. Thanigaivelan, Electrochemical micromachining of galvanized iron sheets: process optimization and performance evaluation, Journal of Electrochemical Science and Engineering 15 (2025) 2821. https://doi.org/10.5599/jese.2821 DOI: https://doi.org/10.5599/jese.2821
[21] V. Palaniswamy, T. Rajasekaran, Performance of magnetized tool in electrochemical micromachining on scrapped alloy wheel matrix composite, Journal of Electrochemical Science and Engineering 13 (2023) 553-561. https://doi.org/10.5599/jese.1660 DOI: https://doi.org/10.5599/jese.1660
[22] R. Health Royal Hermonson, R.Thanigaivelan, V. Kavya, K. Rathinasamy, T. Jagadeesha, Performance of electrochemically deposited hydroxyapatite on textured 316L SS for applications in biomedicine, Surface Engineering 39 (2023) 882-891. https://doi.org/10.1080/02670844.2023.2265616 DOI: https://doi.org/10.1080/02670844.2023.2265616
[23] V. Palaniswamy, K. Seeniappan, T. Rajasekaran, N. Lakshmaiya, Enhancing MRR and accuracy with magnetized graphite tool in electrochemical micromachining of copper: original scientific paper, Chemical Industry & Chemical Engineering Quarterly 29 (2023) 201-208. https://doi.org/10.2298/CICEQ220731027P DOI: https://doi.org/10.2298/CICEQ220731027P
[24] R. Thanigaivelan, R. M. Arunachalam, C. Madhan, R. R. Kumar, M. Muthuselvam, Impact of electrochemical passivation on Burr suppression of Ti–4Al–6V alloy during machining, Surface Engineering and Applied Electrochemistry 55 (2019) 424-429. https://doi.org/10.3103/S106837551904015X DOI: https://doi.org/10.3103/S106837551904015X
[25] N. Sivashankar, R. Thanigaivelan, L. Selvarajan, K. Venkataramanan, Investigation of electrochemical micromachining on magnesium alloy using hollow tool electrode, Ultrasonics 147 (2025) 107526. https://doi.org/10.1016/j.ultras.2024.107526 DOI: https://doi.org/10.1016/j.ultras.2024.107526
[26] R. Thanigaivelan, N. Rajan, M. Soundarrajan, R. Priya, Influence of mixed electrolyte in electrochemical micromachining on SS316L, Manufacturing Technology Today 20(7-8) (2021) 16-25. https://mtt.cmti.res.in/index.php/journal/article/view/9
[27] S. Maniraj, R. Thanigaivelan, Effect of electrode heating on performance of electrochemical micromachining, Materials and Manufacturing Processes 34 (2019) 1494-1501. https://doi.org/10.1080/10426914.2019.1655153 DOI: https://doi.org/10.1080/10426914.2019.1655153
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Nethaji Subash Chandra Bose Ayyavoo, Saravanan Kandasamy Ganesan, Thirunavukkarasu Raja, Vinod Kumaar Jeevarathnam Ravi Kumar, Lakshmanan Sankaralingam, Kumar Subramanian, Karthikeyan Saminathan, Thangavel Thirugnanasambandham

This work is licensed under a Creative Commons Attribution 4.0 International License.



