Pulse electrodeposition of nickel-nitride composite coating and its oxidation under heating treatment

Original scientific paper

Authors

  • Esmar Budi Department of Physics Education, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia and Department of Physics, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia https://orcid.org/0000-0002-7960-0839
  • Teguh Budi Prayitno Department of Physics, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia https://orcid.org/0000-0001-7021-6729
  • Afrizal Department of Chemistry, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia https://orcid.org/0000-0003-0334-5111
  • Hadi Nasbey Department of Physics Education, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia https://orcid.org/0000-0003-2883-9943
  • Riser Fahdiran Department of Physics, Faculty of Mathematics and Science, Universitas Negeri Jakarta, Jl. Rawamangun Muka Raya, Jakarta 13220 Indonesia https://orcid.org/0000-0002-3128-1074
  • Md Nizam Abd Rahman Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, Durian Tunggal, Melaka 76100, Malaysia https://orcid.org/0000-0001-6563-554X

DOI:

https://doi.org/10.5599/jese.2619

Keywords:

Nickel based composite, pulse current density, microwave heating, coating microstructure, coating hardness

Abstract

Nickel-based composite coatings exhibit increased mechanical and oxidation properties due to utilization of reinforced particles as co-deposits within the nickel matrix. Meanwhile, pulse current electrodeposited composite coatings have higher mechanical properties compared to direct current electrodeposited coatings, since they provide a smaller electric force by which nickel ions are captured by particles and inhibit the grain growth of nickel. However, particles near the cathode surface cannot be reloaded in time, leading to lower adsorption of nickel ions on the particle surfaces. In this study, Ni-AlN composite coatings were developed using pulse current electrodeposition at 0.4 to 0.8 mA mm-2. The surface modification of the composite coating was performed by using microwave heating at a temperature of 700 °C for 2 hours. The results showed that Ni and AlN reveal cubic crystal structures of the composite coating. The highest hardness coating was obtained by the sample deposited at 8 mA mm-2. After microwave heating, the surface morphology is composed of microspheres and irregular particles. XRD analysis results suggested that the high temperature oxidation of Ni-AlN composite coating causes the formation of nickel and aluminium oxide. Post-heated coating samples showed a higher hardness than pre-heated. However, for samples deposited at the highest pulse current density, the hardness is lower due to the formation of a weak particle-matrix interface.

Downloads

Download data is not yet available.

References

[1] Z. Quanqing, H. Lijie, H. Chunlai, Z. Zhiru, L. Yang, W Liqiang, Influence of Y2O3 content on the properties of Ni-Y2O-MgO nanocomposite coatings prepared by pulse electrodeposition, International Journal of Electrochemical Science 19 (2024) 100769. https://doi.org/10.1016/j.ijoes.2024.100769

[2] N. Kothanam, K. Harachai, H. Chatpawee, Y. Boonyongmaneerat, N. Triroj, J. Qin, P. Jaroenapibal, Enhanced particle incorporation for co-electrodeposited Ni-P/diamond coatings with a pulse stirring technique, Applied Surface Science Advances 18 (2023) 100499. https://doi.org/10.1016/j.apsadv.2023.100499

[3] Y. Xu, Y. Gao, M. Fan, X. Lu, Y. Chen, Q. Zhao, Preparation and investigation of pulse co-duplek nanoparticles reinforce Ni-Mo coatings under different electrodeposition parameters, Ceramics International 48 (2022) 29629-29640. http://dx.doi.org/10.1016/j.ceramint.2022.06.217

[4] P. Sivasakhti, M.V. Sangaranarayanan, Influence of pulse and direct current on electrodeposition of Ni Gd2O3 nanocomposite for micro hardness, wear resistance and corrosion resistance applications, Composites Communication 13 (2019) 134-142. https://doi.org/10.1016/j.coco.2019.04.008

[5] F. Xia, C. Li, C. Ma, Q. Li, H. Xing, Effect of pulse current density on microstructure and wear property of Ni-TiN nanoparticles deposited via pulse electrodeposition, Applied Surface Science 538 (2021) 148139. https://doi.org/10.1016/j.apsusc.2020.148139

[6] F. Dogan, M. Uysal, H. Algul, E. Duru, H. Akbulut, S. Aslan, Optimization of pulsed electro co-deposition for Ni-B-TiN composites and the variation of tribological and corrosion behaviours, Surface and Coatings Technology 400 (2020) 126209. https://doi.org/10.1016/j.surfcoat.2020.126209

[7] H. Zhang, J. Wang, Q. Li, S. Chen, C. Ma, Microstructure and performance of magnetic field assisted pulse electrodeposited Ni-TiN thin coatings with various TiN grain sizes, Ceramic International 47 (2021) 18532-18539. http://dx.doi.org/10.1016/j.ceramint.2021.03.176

[8] K.L. Zheng, X.S. Wei, B. Yan, P.F. Yan, Ceramic waste SiC particle-reinforced Al matrix composite brake materials with a high friction coefficient, Wear 458-459 (2020) 203424. https://doi.org/10.1016/j.wear.2020.203424

[9] R. Zhu, C. Zhu, S. Wu, X. Wan, G. Li, Effect of CeO2 on microstructure and properties of Ni-Co-based coatings, Journal of Materials Research and Technology 23 (2023) 7329-7339. https://doi.org/10.1016/j.jmrt.2023.09.108

[10] L. Lan, W. Xuan, J. Wang, C. Li, Z. Ren, J. Yu, J. Peng, Interfacial microstructure of partial transient liquid phase bonding of Si3N4 to nickel-base superalloy using Ti/Au/Ni interlayers, Vacuum 130 (2016) 105-108. https://doi.org/10.1016/j.vacuum.2016.04.033

[11] L. Hongtao, Z. Qingqing, D. Yilong, D. Bo, L. Jianguo, Enhancing corrosion and wear resistance of Nickel–aluminum bronze through laser-cladded amorphous-crystalline composite coating, Smart Materials in Manufacturing 2 (2024) 100046. https://doi.org/10.1016/j.smmf.2024.100046

[12] D. Gao, Z. Shen, K. Chen, X.Z. Zhou, H. Liu, J. Wang, Y. Li, Z. Liu, H. Deng, W.Y. Wang, X. Zheng, Review of progress in calculation and simulation of high-temperature oxidation, Progress in Materials Science 147 (2025) 101348. http://dx.doi.org/10.1016/j.pmatsci.2024.101348

[13] P. Gaurav, H. Vasudev, A review on the processing of various coating materials using surface modification techniques for high-temperature solid particle erosion applications, Results in Surfaces & Interfaces 14 (2024) 00167. http://dx.doi.org/10.1016/j.rsurfi.2023.100167

[14] X. Yiku, L. Wenting, L. Binjuan, Q. Changhao, H. Rimin, Z. Qinyang, C. Yongnan, Enhancement of wear and corrosion resistance of pulsed electrodeposited Ni–Mo amorphous/nanocrystalline coatings by heat treatment, Vacuum 229 (2024) 113549. https://doi.org/10.1016/j.vacuum.2024.113549

[15] C.D. Prasad, S. Joladarashi, M.R. Ramesh, M.S. Srinath, B.H. Channabasappa, Effect of microwave heating on microstructure and elevated temperature adhesive wear behavior of HVOF deposited CoMoCrSi-Cr3C2, Surface and Coatings Technology 374 (2019) 291-304. https://doi.org/10.1016/j.surfcoat.2019.05.056

[16] F. Xia, H. Xu, C. Liu, J. Wang, J. Ding, C. Ma, Microstructures of Ni–AlN composite coatings prepared by pulse electrodeposition technology, Applied Surface Science 271 (2013) 7-11. https://doi.org/10.1016/j.apsusc.2012.12.064

[17] R. Swadzba, P. P. Bauer, Microstructure formation and high temperature oxidation behavior of Ti-Al-Cr-Y-Si coatings on TiAl, Applied Surface Science 562 (2021) 150191. https://doi.org/10.1016/j.apsusc.2021.150191

[18] M. Singh, V.K. Gupta, A. Bansal, Y. Sharma, High temperature oxidation behaviour of NiCrAlY clad developed on SS-304 through microwave irradiation, Results in Surfaces and Interfaces 14 (2024) 100179. https://doi.org/10.1016/j.rsurfi.2023.100179

[19] Y. Tian, H. Xiao, C. You, J. Feng, Y. Xiao, X. Zhou, High-temperature oxidation and wear properties of laser cladded Ti-Al-N composite coatings, Transactions of Nonferrous Metals Society of China 33 (2023) 1779. https://doi.org/10.1016/S1003-6326(23)66221-1

[20] J. Du, Y. Li, F. Li, X. Ran, X. Zhang, X. Qi, Research on the high temperature oxidation mechanism of Cr3C2 NiCrCoMo coating for surface remanufacturing. Journal of Materials Research and Technology 10 (2021) 565-579. https://doi.org/10.1016/j.jmrt.2020.12.049

[21] C. Wang, J. Huang, Y. Wang, Preparation and properties of α-Al2O3 diffusion barrier on stainless steel 316, Corrosion Communications 8 (2022) 18-26. https://doi.org/10.1016/j.corcom.2022.04.004

[22] E. Budi, M.N.A. Rahman. Review on Nickel Nitride Composite Coatings, Journal of Physics: Conference Series 286 (2024) 012028. https://doi.org/10.1088/1742-6596/2866/1/012028

[23] H. Li, Y. He, T. Hea, Y. Fan, Q. Yang, Y.Q. Zhan, The influence of pulse plating parameters on microstructure and properties of Ni-W-Si3N4 nanocomposite coatings, Ceramics International 42 (2016) 18380-18392. https://doi.org/10.1016/j.ceramint.2016.08.171

[24] M. S. Chandrasekar, M. Pushpavanam, Review article pulse and pulse reverse platting-Conceptual. Advantages and Application pulse dan pulse reverse, Elctrochimica Acta 53 (2008) 3313-3322. http://dx.doi.org/10.1016/j.electacta.2007.11.054

[25] X. Zhu, C. Cai, G. Zheng, Z. Zhang, J. Li, Electrodeposition and corrosion behavior of nanostructured Ni-TiN composite films, Transactions of Nonferous Metal Society of China 21 (2011) 2216-2224. https://doi.org/10.1016/S1003-6326(11)60998-9

[26] A. A. Aal, M. Bahgat, M. Radwan, Nanostructured Ni–AlN composite coatings. Surfaces and Coating Technology 201 (2006) 2910-2918. http://dx.doi.org/10.1016/j.surfcoat.2006.06.002

[27] N. Erdogan, A.T. Astarlioglu, B. Cagan, N.B. Kilic, M. Erdogan, Pulsed Current Electrodeposition of Gold Nanostructures on ITO: Control of Particle Density and Optical Transmission, Results in Optics 12 (2023) 100471. https://doi.org/10.1016/j.rio.2023.100471

[28] M. S. Khan, M. Farhan, O. Fayyaz, R. A. Shakoor, Effect of AlN nanoparticle concentration in the electrolyte on corrosion resistance and mechanical properties of the electrodeposited composite coatings, Materials Today Communication 38 (2024) 108330. https://doi.org/10.1016/j.mtcomm.2024.108330

[29] A. Fukunaga, S. Ueda, Pulse electrodeposition of Ni–P alloy coatings from Watts baths: P content, current efficiency, and internal stress, Electrochimica Acta 502 (2024) 144839. https://doi.org/10.1016/j.electacta.2024.144839

[30] L. Tian, G. Lv, M. Liu, X. Lei, W. Rao, L. Liao, Reviews: Microwave-induced oxidation technology and its applications, Progress in Natural Science: Materials International 32 (2022) 665-673. https://doi.org/10.1016/j.pnsc.2022.10.005

[31] M. Sajjadnejad, S. Y. S. Haghshenas, P. Badr, N. Setoudeh, S. Hosseinpour, Wear and tribological characterization of nickel matrix electrodeposited composite: A review, Wear 486-487 (2021) 204098. https://doi.org/10.1016/j.wear.2021.204098

Downloads

Published

03-06-2025

Issue

Vol. 15 No. 4 (2025)

Section

Electrodeposition and coatings

License

Copyright (c) 2025 Esmar Budi, Teguh Budi Prayitno, Afrizal, Hadi Nasbey, Riser Fahdiran, Md Nizam Abd Rahman

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

Pulse electrodeposition of nickel-nitride composite coating and its oxidation under heating treatment: Original scientific paper. (2025). Journal of Electrochemical Science and Engineering, 15(4), 2619. https://doi.org/10.5599/jese.2619

Funding data

Similar Articles

1-10 of 398

You may also start an advanced similarity search for this article.