Effect of sintering temperature and time on corrosion characteristics of aluminum matrix composites

Original scientific paper

Authors

DOI:

https://doi.org/10.5599/jese.1891

Keywords:

Aluminum-based composite, powder metallurgy, sintering parameters, silicon carbide
Graphical Abstract

Abstract

Aluminum matrix composites outperform traditional alloys in terms of mechanical properties and corrosion resistance. Silicon carbide is the main reinforcing material in aluminum-based composites that have developed rapidly in recent years. In this investigation, aluminum-silicon carbide composites were prepared through powder metallurgy with 10 and 20 wt.% of silicon carbide reinforcement. The influence of the SiC content, sintering temperature, and sintering time on the corrosion behavior of prepared Al-SiC composites in 0.5 M hydrochloride acid solution was assessed. The surface microstructure was characterized by scanning electron microscopy with energy dispersive analysis and X-rays. The experimental results demonstrated how the sintering parameters can affect the corrosion characteristics of sintered samples. The electrochemical analysis curves showed that when increasing the sintering temperature and sintering time, there is a possibility of self-repair of damaged passive film on the surface while further reinforcing of the composite with silicon carbide prevents penetration of chloride ions. The SEM images and EDS analysis of composite surfaces after being corroded in 0.5 M HCl revealed that increasing the sintering temperature and prolonging the sintering time reduce the pitting corrosion of composites.

Downloads

Download data is not yet available.

References

E. M. Sharifi, M. H. Enayati, F. Karimzadeh, Fabrication and Characterization of Al-Al4C3 nanocomposite by mechanical alloying, International Journal of Modern Physics: Conference Series 05 (2012) 480-487. https://doi.org/10.1142/S2010194512002371

S. M. Mahdi, L. Ghalib, Corrosion Behavior of Al/SiC Composite Prepared by Powder Metallurgy in Chloride Environments, Journal of Bio-and Tribo-Corrosion 8 (2022) 8. https://doi.org/10.1007/s40735-021-00612-6

R.A. Kumar, A. Devaraju, A comparative investigation on cast and aging (T6) response on mechanical and dry sliding wear behavior of Al7075/SiC p metal matrix composite, Surface Review and Letters 28 (2021), no. 06, 2150044. https://doi.org/https://doi.org/10.1142/S0218625X2150044X

R. A. Kumar, M. Sujithkumar, P. Vikram, S. Arunkumar, S. T. Selvan, G. S. Sharan, A review on tribological behaviour of aluminium metal matrix composites, AIP Conference Proceedings: Recent trends in Science and Engineering 2393(1) (2022) 020006. https://doi.org/10.1063/5.0079693

F. Adel, L. Ghalib, Improving the mechanical properties of glass ionomer cements by incorporation of date seed microparticles, Emergent Materials 5 (2023) 1081-1088. https://doi.org/10.1007/s42247-023-00511-1

M. Rahimian, N. Ehsani, N. Parvin, H. R. Baharvandi, The effect of particle size, sintering temperature and sintering time on the properties of Al–Al2O3 composites, made by powder metallurgy, Journal of Materials Processing Technology 209(14) (2009) 5387-5393. https://doi.org/10.1016/j.jmatprotec.2009.04.007

R. A. Kumar, A. Devaraju, Modeling of mechanical properties and high temperature wear behavior of Al7075/SiC/CRS composite using RSM, Silicon 13(10) (2021) 3499-3519. https://doi.org/10.1007/s12633-020-00801-x

R. A. Kumar, B. I. Prasad, C. Bibin, I. J. Thomas, G. Soundararajan, P. R. Darshan, S. Arunkumar, Physical and mechanical characterization of Al7075/Si3N4 metal matrix composite prepared by stir casting technique, MaterialsToday: Proceedings 80 (2023) 176-182. https://doi.org/10.1016/j.matpr.2022.11.096

R. A. Kumar, A. Devaraju, S. Arunkumar, Experimental investigation on mechanical behaviour and wear parameters of tic and graphite reinforced aluminium hybrid composites, MaterialsToday: Proceedings 5(6) (2018) 14244-14251. https://doi.org/10.1016/j.matpr.2018.03.005

A. S. Channi, H. S. Bains, J. S. Grewal, V. S. Chidambranathan, R. Kumar, Tool wear rate during electrical discharge machining for aluminium metal matrix composite prepared by squeeze casting: A prospect as a biomaterial, Journal of Electrochemical Science and Engineering 13 (1) (2023) 149-162. https://doi.org/10.5599/jese.1391

R. T. Loto, P. Babalola, Analysis of SiC grain size variation and NaCl concentration on the corrosion susceptibility of AA1070 aluminium matrix composites, Cogent Engineering 5(1) (2018) 1473002. https://doi.org/10.1080/23311916.2018.1473002

R. A. Kumar, D. Ayyappan, S. Arunkumar, G. Devanand, K. Dasar, N. S. Srivatsav, S. Dhamodharan, A Comprehensive review on fabrication techniques and corrosion behavior on metal matrix composites, AIP Conference Proceedings: Recent Trends in Science and Engineering 2393 (2022) 020014. https://doi.org/10.1063/5.0074274

H. A. Abdulghani, L. Ghalib, B. J. Nabhan, Spot Welding Parameters Effect on Surface Corrosion Behavior of Carbon Steel Sheet, Egyptian Journal of Chemistry 65(10) (2022) 531-535. https://doi.org/10.21608/EJCHEM.2022.117260.5291

S. Guo, A. Chu, H. Wu, C. Cai, X. Qu, Effect of sintering processing on microstructure, mechanical properties and corrosion resistance of Ti–24Nb–4Zr–7.9 Sn alloy for biomedical applications, Journal of Alloys and Compounds 597 (2014) 211-216. https://doi.org/10.1016/j.jallcom.2014.01.087

P. Gupta, D. Kumar, M. Quraishi, O. Parkash, Effect of sintering parameters on the corrosion characteristics of iron-alumina metal matrix nanocomposites, Journal of Materials and Environmental Science 6(1) (2015) 155-167. https://www.jmaterenvironsci.com/Document/vol6/vol6_N1/19-JMES-1006-2014-Gupta.pdf

G. Veerappan, M. Ravichandran, M. Meignanamoorthy, V. Mohanavel, Characterization and properties of silicon carbide reinforced Ni-10Co-5Cr (Superalloy) matrix composite produced via powder metallurgy route, Silicon 13(4) (2021) 973-984. https://doi.org/10.1007/s12633-020-00455-9

L. M. Azaath, U. Natarajan, G. Veerappan, M. Ravichandran, S. Marichamy, Experimental Investigations on the Mechanical Properties, Microstructure and Corrosion Effect of Cu-20Al-4Ni/SiC Composites Synthesized Using Powder metallurgy Route, Silicon 14 (2022) 5993-6002. https://doi.org/10.1007/s12633-021-01363-2

Z. Ahmad, P. Paulette, B. A. Aleem, Mechanism of localized corrosion of aluminum–silicon carbide composites in a chloride containing environment, Journal of Materials Science 35 (2000) 2573-2579. https://doi.org/10.1023/A:1004767113052

L. Ghalib, A. K. Muhammad, S. M. Mahdi, Study the effect of adding titanium powder on the corrosion behavior for spot welded low carbon steel sheets, Journal of Inorganic and Organometallic Polymers and Materials 31(6) (2021) 2665-2671. https://doi.org/10.1007/s10904-020-01863-5

M. N. Rahaman, Ceramic Processing and Sintering, CRC Press, Taylor & Francis Group, Boca Raton, 2017. https://doi.org/10.1201/9781315274126

M. Asadikiya, C. Zhang, C. Rudolf, B. Boesel, A. Agarwal, Y. Zhong, The effect of sintering parameters on spark plasma sintering of B4C, Ceramics International 43(14) (2017) 11182-11188. https://doi.org/10.1016/j.ceramint.2017.05.167

V. V. Vani, S. K. Chak, The effect of process parameters in aluminum metal matrix composites with powder metallurgy, Manufacturing Review 5 (2018) 7. https://doi.org/10.1051/mfreview/2018001

R. T. Loto, M. M. Solomon, Corrosion resistance and passivation behavior of 3004 AlMnMg and 4044AlSi aluminum alloys in acid-chloride electrolytes, Materials Research Express 8(9) (2021) 096529. https://doi.org/10.1088/2053-1591/ac286b

S. Esmailzadeh, M. Aliofkhazraei, H. Sarlak, Interpretation of cyclic potentiodynamic polarization test results for study of corrosion behavior of metals: a review, Protection of Metals and Physical Chemistry of Surfaces 54(5) (2018) 976-989. https://doi.org/10.1134/S207020511805026X

M. Pech-Canul, M. Makhlouf, Processing of Al–SiCp metal matrix composites by pressureless infiltration of SiCp preforms, Journal of Materials Synthesis and Processing 8 (2000) 35-53. https://doi.org/10.1023/A:1009421727757

M. Aruna, S. Arivukkarasan, Electrochemical behavior of Al-SiC metal matrix composites, International Journal of Applied Engineering Research 15(1) (2020) 1-4. https://www.ripublication.com/ijaer20/ijaerv15n1_01.pdf

Downloads

Published

26-07-2023 — Updated on 26-07-2023

How to Cite

Mahdi, S. M., & Ghalib, L. (2023). Effect of sintering temperature and time on corrosion characteristics of aluminum matrix composites: Original scientific paper. Journal of Electrochemical Science and Engineering, 13(6), 1015–1026. https://doi.org/10.5599/jese.1891

Issue

Section

Corrosion