Microstructural and mechanical properties of CNT-reinforced ZrO2-Y2O3 coated boiler tube steel T-91

Original scientific paper

Authors

  • Sandeep Kumar Department of Mechanical Engineering, Guru Kashi University, Bathinda, Punjab, India https://orcid.org/0000-0001-7711-8988
  • Rakesh Bhatia Yadavindra Department of Engineering, Punjabi University Guru Kashi Campus, Damdama Sahib, India https://orcid.org/0000-0002-0320-3845
  • Hazoor Singh Yadavindra Department of Engineering, Punjabi University Guru Kashi Campus, Damdama Sahib, India
  • Roshan Lal Virdi Department of Mechanical Engineering, Punjabi University, Patiala, India https://orcid.org/0000-0003-0571-5374

DOI:

https://doi.org/10.5599/jese.1228

Keywords:

Carbon nano tubes (CNT’s), plasma spray, porosity, hardness
Graphical Abstract

Abstract

The main purpose of this study was to fabricate carbon nanotubes (CNTs) reinforced zircon­nium yttrium coatings on boiler tube steel and to investigate the microstructural and mechanical properties of these coatings. Plasma sprayed conventional ZrO2-Y2O3, ZrO2-Y2O3 and 1 wt.% CNT and ZrO2-Y2O3 and 4 wt.% CNT were prepared and deposited successfully on boiler tube steel material T-91 (ASTM SA-213) by plasma thermal spray technology. Microhardness, porosity, XRD (X-ray diffraction), SEM/EDAX (scanning elec­tron microscopy/energy dispersive X-ray spectroscopy), X-ray mapping and cross-sectional analyses were used to analyse the specimens. The hardness of CNT reinforced ZrO2-Y2O3 increased with the increase in the percentage of CNT, whereas the porosity of the composite coatings decreased with the increase in the CNT percentage. The observed increase in hardness may be attributed to the content of CNT in the composite coating. The present research gives important information related to the fabrication and physical characteristics of CNT-reinforced ZrO2-Y2O3 coatings deposited on T-91 boiler tube steel.

Downloads

Download data is not yet available.

References

M. Esfandiari, H. Dong, Surface and Coatings Technology 202(3) (2007) 466-478. https://doi.org/10.1016/j.surfcoat.2007.06.069

R. A. Rapp, Corrosion Science 44(2) (2002) 209-221. https://doi.org/10.1016/S0010-38X(01)00057-9

D. Sapundjiev, Corrosion Science 48(3) (2006) 577-594. https://doi.org/10.1016/j.corsci.2005.04.001

R. Sivakumar, S. V. Joshi, Transactions of Indian Ceramic Society 50(1) (1991) 1-14. https://doi.org/10.1080/0371750X.1991.10804475

H. Zhang, H. Lua, Y. Zhu, F. Li, R. Duan, M. Zhang, X. Wang, Powder Technology 227 (2012) 9-16. https://doi.org/10.1016/j.powtec.2012.02.007

B. Bhushan, B. K. Gupta, Handbook of Tribology: Materials, Coatings, and Surface Treatments McGraw-Hill, New York (1991) 259. https://www.osti.gov/biblio/441774

K. Szyma, A. Hernas, G. Moskal, H. Myalska, Surface and Coatings Technology 268 (2015) 153-164. https://doi.org/10.1016/j.surfcoat.2014.10.046

N. Kahraman, B. Gülenc, Materials & Design 23(8) (2002) 721-725. https://doi.org/10.1016/S0261-3069(02)00075-4

H. S. Sidhu, B. S. Sidhu, S. Prakash, Journal of Materials Processing Technology 171(1) (2006) 77-82. https://doi.org/10.1016/j.jmatprotec.2005.06.058

S. Deshpande, A. Kulkarni, S. Sampath, H. Herman, Surface and coatings Technology, 187(1) (2004) 6-16. https://doi.org/10.1016/j.surfcoat.2004.01.032

S. Kamal, R. Jayaganthan, S. Prakash, Surface Coatings Technology 203(8) (2009) 1004-1013 https://doi.org(10.1016/j.surfcoat.2008.09.031

S. Iijima, Nature 354 (1991) 56-58. https://doi.org/10.1038/354056a0

R. S. Ruoff, D. C. Lorents, Carbon 33(7) (1995) 925-930. https://doi.org/10.1016/0008-6223(95)00021-5

M. S. Dresselhaus, G. Dresselhaus, P. C. Eklund, Sci. Fullerenes Carbon Nanotube 917 (1996) 870-917. https://doi.org/10.1016/b978-012221820-0/50020-4

M. Sharma, V. Sharma, International Journal of Minerals, Metallurgy, and Materials 23(2) (2016) 222-233. https://doi.org/10.1007/s12613-016-1230-3

K. Goyal, H. Singh, R. Bhatia, Advanced Engineering Forum 26 (2018) 53-66. https://doi.org/10.4028/www.scientific.net/AEF.26.53

E. T. Thostenson, C. Li, T. W. Chou, Composites Science and Technology 65(3) (2005) 491-516. https://doi.org/10.1016/j.compscitech.2004.11.003

C. F. Deng, D. Z. Wang, X. X. Zhang, A. B. Li, Materials Science and Engineering A 444(1) (2007)138-145. https://doi.org/10.1016/j.msea.2006.08.057

M. K. Singla, H. Singh, V. Chawla, Journal of Minerals and Materials Characterization and Engineering 10(8) (2011) 717-726.

B. M. Praveen, T. V Venkatesha, Y. A. Naik, K. Prashantha, Surface and Coatings Technology 201(12) (2007) 5836-5842. https://doi.org/10.1016/j.surfcoat.2006.10.034

K. Balani, S. P. Harimkar, A. Keshri, Y. Chen, N. B. Dahotre, A. Agarwal, Acta Materialia 56(20) 5984-5994. https://doi.org/10.1016/j.actamat.2008.08.020

I. Ahmad, M. Unwin, H. Cao, H. Chen, H. Zhao, A. Kennedy, Y. Q. Zhu, Composites and Science Technology 70(8) (2010) 1199-1206. https://doi.org/10.1016/j.compscitech.2010.03.007

A. K. Keshri, V. Singh, J. Huang, S. Seal, W. Choi, A. Agarwal, Surface and Coatings Technology 204(11) (2010) 1847-1855. https://doi.org/10.1016/j.surfcoat.2009.11.032

M. O. Bodunrin, K. K. Alaneme, L. H. Chown, Journal of Materials Research and Technology 4(4) (2015) 434-445. https://doi.org/10.1016/j.jmrt.2015.05.003

C. F. Gutierrez-Gonzalez, A. Smirnov, A. Centeno, A. Fernández, B. Alonso, V. G. Rocha, R. Torrecillas, A. Zurutuza, J. F. Bartolome, Ceramics International 41(6) (2015) 7434-7438. https://doi.org/10.1016/j.ceramint.2015.02.061

K. Goyal, World Journal of Engineering 15(4) (2018) 429-439. https://doi.or/10.1108/WJE-10-2017-0315

H. Chen, X. Zhou, C. Ding, Journal of the European Ceramic Society 23(9) (2003) 1449-1455. https://doi.org/10.1016/S0955-2219(02)00345-X

K. Goyal, H. Singh, and R. Bhatia, Journal of the Australian Ceramic Society 55(2) (2019) 315-322. https://doi.org/10.1007/s41779-018-0237-9

B. S. Sidhu, D. Puri, S. Prakash, Journal of Materials Processing Technology 159(3) (2005) 347-355. https://doi.org/10.1016/j.jmatprotec.2004.05.023

K. Katiki, S. Yadlapati, S. N. S. Chidepudi, P. R. Hari, International Journal of ChemTech Research 6(11) (2014) 4579-4584. https://www.sphinxsai.com/2014/ch_vol6_no11/1/(4579-4584)N14.pdf

J. Mehta, V. K. Mittal, and P. Gupta, Journal of Applied Science and Engineering 20(4) (2017) 445-452. https://doi.org/10.6180/jase.2017.20.4.05

S. S. Chatha, H. S. Sidhu, B. S. Sidhu, Journal of Minerals & Materials Characterization & Engineering 11(06) (2012) 569-586. https://doi.org/10.4236/jmmce.2012.116041

P.-H. Gao, Y.-G. Li, C.-J. Li, G.-J. Yang, C.-X. Li, Journal of Thermal Spray Technology 17 (2008) 742-749. https://doi.org/10.1007/s11666-008-9258-1

A. Pathak, S. Mathiyalagam, K. K. Pandey, P. Bijalwan, M. Dutta, A. K. Keshri, International Journal of Applied Ceramic Technology 16(6) (2019) 2306-2315. https://doi.org/10.1111/ijac.13327

W. Guo, H. Y. Tam, The International Journal of Advanced Manufacturing Technology 72 (2014) 269-275. https://doi.org/10.1007/s00170-014-5661-6

J. Ning, J. Zhang, Y. Pan, J. Guo, Materials Science and Engineering A 357(1–2) (2003) 392-396. https://doi.org/10.1016/S0921-5093(03)00256-9

E. Edward Anand, S. Natarajan, Journal of Materials Engineering and Performance 24(1) (2015) 128-135. https://doi.org/10.1007/s11665-014-1306-z

P. R. Silva, V. O. Almeida, G. B. MacHado, E. V. Benvenutti, T. M. H. Costa, M. R. Gallas, Langmuir 28(2) (2012) 1447-1452. https://doi.org/10.1021/la203056f

A. K. Keshri, A. Agarwal, Surface and Coatings Technology 206(2-3) (2011) 338-347. https://doi.org/10.1016/j.surfcoat.2011.07.025

B. Singh, D. Puri, S. Prakash, Journal of Materials Processing Technology 159(3) (2005) 347-355. https://doi.org/10.1016/j.jmatprotec.2004.05.023

C. F. Deng, D. Z. Wang, X. X. Zhang, A. B. Li, Materials Science and Engineering A 444(1-2) (2007) 138-145. https://doi.org/10.1016/j.msea.2006.08.057

Downloads

Published

26-07-2022

How to Cite

Kumar, S. ., Bhatia, R., Singh, H., & Virdi, R. L. . (2022). Microstructural and mechanical properties of CNT-reinforced ZrO2-Y2O3 coated boiler tube steel T-91: Original scientific paper. Journal of Electrochemical Science and Engineering, 12(5), 877–888. https://doi.org/10.5599/jese.1228

Issue

Section

Electrodeposition and coatings